WHY2025 wiki - User contributions [en]

Badge Issues

2025-08-18T09:21:27Z

Stored: /* Unanswered */

== Please edit this page ==

'''Please edit this page to add your issue or increase the interest counter
'''

The ''[number]'' in front of each question is the interest counter. Increase it by one if you have the same question.

== Badge Hardware Questions/Issues ==
=== Answered ===
==== [1] After reflash and exiting the intial sponsors screen, the screen stays blue ====
* => Reflash the badge using the web flasher. (https://why-prog.heplaphon.com/). Use the USB socket on the left side for flashing. After the update unplug/replug the USB. Make sure to use a good cable as the badge is power hungry.
==== [2] How do I reset the badge on battery? ====
* => Applying usb power will reset the badge
==== [4] Batteries ar being held firmly (maybe a bit too firmly) in place in the battery holder. How can I safely remove the batteries? What tool to use for this without damaging the batteries or the PCB? ====
* => Try gripping it with rubber gloves on.
* => For future handling, add strong tape around it, so that you'll have a lid to pull on for extra support

==== [3] The badge suddenly stopped working. Serial shows boot-loop with message <pre>Cannot connect to target. Error: TIMEOUT </pre> ====
* => Reseating the ESP daughterboard (fitted with a screw) helped here.
* => M.2 socket of ESP daughterboard can break off without being immediately visible. This also leads to this error. [https://chaos.social/@xro/115011118785473303 Re-soldering fixed it.]
Trace of boot-loop:
<pre>
./idf.py monitor
W (1098) fatfs-sd: SD card not mounted
E (1108) device: The device does not exist SD0
Cannot connect to target. Error: TIMEOUT
Check if the host and the target are properly connected.
E (4828) sdmmc_common: sdmmc_init_ocr: send_op_cond (1) returned 0x107
HINT: Please reboot the board and then try again
E (4828) sdio_wrapper: sdmmc_card_init failed
E (4828) H_SDIO_DRV: sdio card init failed
Crashing in ESP-IDF task
Guru Meditation Error: Core 1 panic'ed (Instruction access fault). Exception was unhandled.

--- Stack dump detected
Core 1 register dump:
MEPC : 0x00000000 RA : 0x00000000 SP : 0x4ff278c0 GP : 0x4ff18580
TP : 0x4ff278e0 T0 : 0x4ff0f4a6 T1 : 0x4ff120a8 T2 : 0xffffffff
--- 0x4ff0f4a6: spinlock_release at /home/bernhard/source/why2025-badge-firmware/components/esp_hw_support/include/spinlock.h:181
</pre>
==== [5] Some keys (the `w` key in my case) don't register. I've tried with the nametag app and with the new System Settings app, and it didn't work on either. ====
[[User:Bytefighter|bytefighter]] ([[User_talk:Bytefighter|talk]]) 01:24, 14 August 2025 (CEST)
* => Check for [https://chaos.social/@edronik/115027350958230845 crusty stuff under the metal membrane]
==== [8] The antenna isn't connected yet. Can I use the device without damaging anything? ====
* The antenna is used by the LoRa radio. At the moment of writing there is no badge firmware available that uses the LoRa radio. This means that for now the device can safely be used without the antenna (socket) attached.
* As soon as you do start using the LoRa radio, there is a potential for damage when the badge is used without the antenna. Attaching the antenna requires some extra precautions. See the instructions on attaching the socket further down on this wiki page for tips and tricks.
** (Can not include link as the HTTP anchor contains square brackets)

==== [2] Where/how to solder the antenna socket/connector? ====

Before soldering on the antenna socket, consider if you really need to. The section of the wiki about using the badge without the antenna attached has some important information.

Steps for soldering:
It's recommended to read through these steps first before you get going.

* Shut down badge. Remove batteries or other power sources.
* Take the badge apart by unscrewing all four screws, removing the front plate and the 3D printed spacer(s).
** The best fitting bit is a J0/JIS0, some iFixit kits have them. A PH0/00 may work but be careful to not strip the screw or poke in to your hand while applying pressure for unscrewing.
* Location: in the top right corner tightly along side the screen, you should now see 5 holes marked as "J5". (See image)
[[File:Badge back antenna socket holes.jpg|thumb|none]]
* Check if your 3D printed spacer has holes in that spot. The socket will be inserted in these holes from the back of the badge. The legs will stick through on the front side of the badge. Once they are soldered the spacer needs to allow some room for the pins to poke through it. If the spacer won't fit, a quick fix would be to widen the holes with you soldering iron, or use a drill to increase the size.
* The center hole of the pattern is for the signal. The surrounding 4 holes are connected to ground and provide points to strengthen the connection between the socket and the PCB. (See image)
[[File:Badge front antenna socket details.jpg|thumb|none]]
* Insert the socket from the back of the PCB. The component should be on the back of the badge where the battery holders are. The legs should stick out on the screen side of the badge.

Note: some of the holes for soldering on the socket are very close to the side of the screen. The screen is delicate and will take damage from the heat of your soldering iron. How to deal with this? (See image)

* Easy:
** Keep your iron away from the side of the screen.
** Solder only the two pins on the outside of the PCB for rigidity, and the center pin for signal. This gives you less than half a centimeter to work with. Be careful with the antenna and socket as
* Expert:
** Put one or more layers of true Kapton tape (M3 5413) on the side of the screen, all the way down to the PCB to protect the screen from heat. (See image)
[[File:Badge front kapton tape.jpg|thumb|none]]
** Still make sure your soldering iron stays away from the screen as much as possible at all times.
** Solder the four outside pins for maximum rigidity and the center pin for signal.
* Possibly hard to execute:
** Ideally you take the screen of which can be done with some dental floss, although this could damage the screen.

=== Unanswered ===
* Got a question that is already listed but not answered yet? The ''[number]'' in front of each question is the interest counter. Edit this wiki and increase the counter by one if you have the same question. This allows us to prioritize. Thank you!
* Got an answer? Please edit the wiki, add your answer and move the question to the Answered section. Thank you for your contribution!
==== [4] Screen flickers sometimes. Is this a defect? I tried looking at the screen ribbon cable, it seems OK. ====
* => (bend the board -> more flicker?)
* => I had to resolder the m.2 connector (use flux and touch every pin with soldering iron)

==== [4] screen is not turning on at all. ====
* => I had to resolder the m.2 connector (use flux and touch every pin with soldering iron)
* => extreme case: (https://chaos.social/@xro/115011118785473303)
* => https://wiki.why2025.org/Badge#m.2_connector

==== [7] Can not turn off badge while charging. ====
Yet to be answered.
==== [9] One battery holder has a big blob of epoxy where it should contact the battery. Is there a good way to remove it? ====
Yet to be answered.
==== [10] Badge updates apps after starting an app that isn't the updater ====
Yet to be answered.
==== [11] Sponsor screen replays (unskippable) after every flash ====

[[User:RobotJoosen|robotjoosen]] 22:11, 14 August 2025 (GMT)

<s>=> Press `fn + x` to skip sponsor screen</s>

[[User:Tielemans.jorim|Tielemans.jorim]] 14:13, 16 August 2025 (CEST)

`fn + x` should not be used as this force closes the sponsors app. You need to wait for it to at least play once and use the `esc` key once shown on screen. Terminating the sponsors app early might result in not being able to open other apps.

==== [12] Double-tapping the power button doesn't shut down the badge ====
Yet to be answered.
==== [13] Where do we get the badge now that the event is over? The lines were huge or the stand was closed. Can we pay for shipping to get them later? ====
Yet to be answered.
==== [14] Is it possible to insert an SD card without removing the daughter board (with cells installed)? ====

[[User:RobotJoosen|robotjoosen]] 22:13, 14 August 2025 (GMT)

=> No, there is not physical space to insert a SD card without bending/breaking it. It is also not possible without the cells.

==== [1] Flashing to `BadgeVMS post_event` might work fine, until a reboot. This appears to happen only on devices with an SD-card installed, it will result in the error `Could not open APPS:[badgevms_launcher]badgevms_launcher.elf` [https://pastebin.com/zMr45zHT pastebin] ====
Yet to be answered.

* Addendum, See also: [https://gitlab.com/why2025/team-badge/firmware/-/issues?show=eyJpaWQiOiI5IiwiZnVsbF9wYXRoIjoid2h5MjAyNS90ZWFtLWJhZGdlL2Zpcm13YXJlIiwiaWQiOjE3MTg4NzgyNX0%3D Boot is stuck, when fitted with an SD card]

==== [2] Damaged wrapping of an 18650 battery, is this an issue? ====
* Is this an issue? (see picture)

[[File:Badge 18650 with a small mark.jpg|thumb|none]]

==== [1] The white overlay(layer) between the keyboard and the PCB is missing, so typing does not work, can I obtain this somewhere? ====
Yet to be answered.
==== [1] Screen wobbles horizontal (X-Axis) with random amount. (Allready flashed newest firmware (Badge VMS post_event) without any changes). Wobble gets worse the longer the device is on. Starts after about 3 Minutes. Slight wobble can be triggert by pressing a button keyboard ====
Yet to be answered.

==== [1] Screen has yellowish pixel failures. Screen also wobbles horizontal after few minutes (see topic above) ====
Yet to be answered.

[[File:PXL 20250815 195829061.jpg|thumb|none]]

==== [1] I'd like to remove the 18650 cell holders but the epoxy is holding them in a bit too well. Has anyone managed to find a non-destructive way to do this? ====

Unofficial answer from the OP... I was able to pry the cell holders loose using a craft knife and a little force. However, this revealed some pools of uncured epoxy, as shown in the photo. The Internet suggests leaving the badge outside for a bit of sunbathing, as the solar UV will help the epoxy to set.

[[File:Badge-post-op.jpg|thumb|none|alt=WHY badge which has had the cell holders removed using a craft knife. Along the long edge of each cell holder there is some pooling of uncured epoxy.|WHY badge with cell holders removed - showing uncured epoxy]]

==== [1] I'd like to power the badge using a conventional LiPo pouch, but I don't see a header anywhere that I could solder a JST connector to. Has anyone else achieved this? ====
Yet to be answered.

==== [2] There's a header (LS1) between the M.2 board and one of the cell holders which seems (from the schematics) to be for a speaker. Has anyone got this working? What parts did you use? ====
Yet to be answered.

My guess is that this is a [https://nl.aliexpress.com/item/1005007755047389.html PH 2.0 horizontal surface mount connector]? Can the team confirm?
[[File:Screenshot 2025-08-18 LS1.png|thumb|none|LS1 connector from photo of prototype]]

==== [1] Badge shows yellow screen randomly (seems related to daughter M.2 board) ====

Randomly the badge display turns yellow.

What I tried:
* Swapped the daughter M.2 ESP board with another badge → the yellow screen issue followed the daughterboard, not the main board.
* Serial log shows no errors at the moment the display turns yellow.
* Tried many different firmwares, currently running the post event firmware.

This suggests the issue is related to the M.2 daughterboard, likely power instability under load.

Yet to be answered.

== Badge User Questions/Issues ==
=== Answered ===
==== [1] Inside program “c64emu” v1 trying Shift+{number} prints the number to console and not the symbol. This behaviour works in “crackme” v3. ====
* Thank you for reporting this, I've fixed this and released a new version with improved keyboard handling (v2.0.1). --[[User:Wallaby|Wallaby]] ([[User talk:Wallaby|talk]]) 14:37, 11 August 2025 (CEST)
==== [5] WHY2025 OTA updater is not reacting. ====
* => We are working on this. For now, don't touch it and instead just wait at least 30 seconds.
** => This didn't work for me; I had to re-flash the firmware. [[User:Bytefighter|bytefighter]] ([[User_talk:Bytefighter|talk]]) 08:53, 13 August 2025 (CEST)
** => Any update on this? "OTA" and "Hello" app don't do anything. Not even an error message. Is there a hidden Wifi settings menu or something for the "over the air" part? Maybe a USB-C to Ethernet dongle?
==== [3] There is a stripe and/or "HD3" stamp on my screen ====
* Test if you see these when the badge is off.
* There is a protective cellophane sheet attached to the screen for protection against scratches and dirt. Remove the cellophane sheet by peeling it off. There's a tab to peel in the lower right corner. This tab may be under the front cover or the spacer.
* I saw at least one device where the sticky tape area was '''under''' the front cover. --[[User:Cybso|Cybso]] ([[User talk:Cybso|talk]]) 00:03, 11 August 2025 (CEST)
** Assemblers of the spacer/keyboard/front cover were at some point instructed to keep the tab to peel of the protective layer under the spacer. Reason for this: unknown. Perhaps to reduce the change of them coming off while the badges were still being assembled. --[[User:44x|44x]] 23:33, 14 August 2025 (CEST)
==== [2] Could do one update, then three updates and then BadgeVMS Firmware Version 4. Now I a offered this update on every boot and can do nothing else, even though I have installed it already ====
* reboot fixes this.
==== [3] My Badge is showing a yellow screen. Its starting with a blue screen and shows the Menu for a few seconds an then turns yellow. What does this indicate? ====
* The v5 firmware had this bug. Reflash with a newer to fix.
==== [11] I’m finally home! How do I connect the badge to my local Wi-Fi? ====
* Lazy, hacky method: Create an open Wi-Fi network with the SSID "WHY2025-open" (the O not as a capital letter) and run the OTA update app.
* Easy method: Use the [https://why-prog.heplaphon.com/ WHY badge flasher] to install the "BadgeVMS post_event" firmware which includes an app called System Settings which allows you to connect to your home Wi-Fi network.
** This requires a desktop Google Chrome or Microsoft Edge. Firefox is not supported.
** The USB cable must be in the socket on the side. Not the bottom.
** The correct COM port is named "USB Serial". Not "USB Jtag/Serial" or "CDC"
?? What if "USB Serial is not showing up ??
* Developer method:
** Clone the badge firmware repository.
** Edit `wifi_config` in `badgevms/drivers/wifi.c`.
** Change `.ssid` to your network name.
** Directly below `.ssid` add a line with `.password = "your network password",`.
** Then build/flash the firmware: `idf.py build flash`.
* Dev-in-a-hurry:
** Collect the latest firmware here: https://gitlab.com/why2025/team-badge/firmware/-/releases
** use esptool.py -p /dev/cu.wch* write_flash 0 firmware_81d7cdf7.bin
** use the System Settings which allows you to connect to your home Wi-Fi network.

==== There's sticky transparent stuff on my badge, what should I do? ====
* The sticky stuff is UV epoxy that is not fully cured.
* It is very much recommended to fully cure the epoxy first.
** If you have touched the sticky epoxy, wash your hands.
** ⚠️ Note that according to the interwebz some people can be allergic to uncured epoxy. It is not ruled out you may see an allergic reaction. Always contact a medical professional if you see effects and have questions.
* Where can I expect epoxy on my badge?
** Epoxy should have been applied to the ends of the battery holders, where the holders are soldered onto the PCB. There are 4 spots in total. In some cases epoxy may not cover the area that needs protecting.
** You may however also observe epoxy in other spots, such as:
*** The back side near the bottom USB-C port and the screw holes, preventing screws from going through.
*** The front side of the badge near the keyboard, which may prevent the keyboard from fully functioning. This includes the area under the white membrane layer. [https://chaos.social/@edronik/115027350958230845 More information from someone who has experienced this].
*** Basically any place liquid could have flowed to from the location the epoxy was applied since the epoxy was runny when it was applied.
* How to cure the epoxy?
** The epoxy is cured by exposing it to UV light. A popular source of UV light is the sun. Even if it is cloudy or somewhat later in the afternoon, UV light is still present so you don't need to put the badge in the scorching sun to cure the epoxy.
** 1. Shut down badge, remove batteries or any other power source. Do not expose those to the hot sun.
** 2. Place your badge outside in daylight. Make sure all spots that have UV resin on them are exposed. In direct sunlight it is recommended to cover other components.
** 3. Leave for 30 to 60 minutes.
** 4. Regularly check and leave exposed to daylight until all blobs of epoxy have fully cured and are no longer sticky at all. Wash hands after every check.

=== Unanswered ===
* Got a question that is already listed but not answered yet? The ''[number]'' in front of each question is the interest counter. Edit this wiki and increase the counter by one if you have the same question. This allows us to prioritize. Thank you!
* Got an answer? Please edit the wiki, add your answer and move the question to the Answered section. Thank you for your contribution!
==== [4] OTA update screen appears on first boot, after pressing space bar, blue screen with nothing happening for over an hour. ====
* Have the same problem after first OTA update. Update started but the device stuck on bluescreen for an hour or so before I removed power. After flashing a new firmware using the [https://why-prog.heplaphon.com web updater] it works again (use the USB slot on the side, otherwise you get an error message "Your ESP C6 chip is unsupported"). [https://pastebin.com/VjMA5ZZA Logfiles] --[[User:Cybso|Cybso]] ([[User talk:Cybso|talk]]) 00:03, 11 August 2025 (CEST)
** No, it doesn't. It displayed the sponsors page once but returned to the bluescreen afterwards. [https://pastebin.com/cCKejKCk Logs from the side USB port]. --[[User:Cybso|Cybso]] ([[User talk:Cybso|talk]]) 00:18, 11 August 2025 (CEST)
** Uploaded another log containing the complete first boot after flashing the new firmware: https://pastebin.com/3NiSRncL (edit: see below). Note the exception at the end: "Task 4 caused an unhandled exception, Cerberos will deal with it". After that, no new entries appear and the display stays blue. --[[User:Cybso|Cybso]] ([[User talk:Cybso|talk]]) 00:25, 11 August 2025 (CEST)
** Was wrong about that again. There were more log entries while I wrote the previous comments. Here is the complete log: https://pastebin.com/KMQwhBPv --[[User:Cybso|Cybso]] ([[User talk:Cybso|talk]]) 00:34, 11 August 2025 (CEST)
* Anyone managed to fix that errpr and getting the Bagde running again? --[[User:Cybso|Cybso]] ([[User talk:Cybso|talk]]) 13:16, 13 August 2025 (CEST)
==== [7] Blue screen. Nothing happening. ====
* => Not official answer: What helped for me was reflashing the badge via the flash station at the badge tent.
* Might be missing symbols, ota might work. Flash, don't reboot yet and ota first.
* Might be because of a known issue regarding the sd card, if you have this issue with an sd card inserted, try again when removing it. See also: [https://gitlab.com/why2025/team-badge/firmware/-/issues?show=eyJpaWQiOiI5IiwiZnVsbF9wYXRoIjoid2h5MjAyNS90ZWFtLWJhZGdlL2Zpcm13YXJlIiwiaWQiOjE3MTg4NzgyNX0%3D Boot is stuck, when fitted with an SD card]

==== [1] Cannot build the firmware from https://gitlab.com/why2025/team-badge/firmware/. Tried to build main and flashed_at_first_handout - both fail because of the following error: https://pastebin.com/H4xwPLhC ====
* Do you have the latest ESP-IDF installed? (Version 5.5)
==== [1] stuck at do_http(https://badge.why2025.org/api/v3/projects/why2025_firmware_ota_c6/rev4/files/version.txt) error: server response: '{"reason":"No app with slug 'why2025_firmware_ota_c6' and revision '4' found"}' ====

==== [5] The badge is not detect on my mac when I connect it by side port: ====
* '''Don't''' use brew, it has been reported not to work.
* Follow these instructions: [[Badge/MacOS_Drivers]]
==== [1] I can't flash the badge - it says the board is incompatible ====
* => Use the USB-C port on the side of the board, not the one on the bottom
==== [1] The letter "a' is represented by a horizontal dash in the nametag app ====
Yet to be answered.
==== [1] The launcher says that "Enter" will launch an app while it really launches when pressing "Space". ====
Yet to be answered.
==== [1] The settings app does react veeeee*ry slowly, sometimes I have to press Enter multiple times to get to the list of WiFi networks (and sometimes, one of those keypresses instantly selects a network) ====
Yet to be answered.
==== [1] I have damaged my screen :c I cannot find the exact parts list, is there some info? Aliexpress Link? :D ====
??

==== [1] How to get the missing apps after reflashing the badge? ====
I have two badges. Badge 1 flashed at the event, and Badge 2 reflashed with "BadgeVMS post-event" using "WHY2025-Open" SSID at home and the web flasher https://why-prog.heplaphon.com/.

Badge 1 shows 11 Applications Available: Game of Life v1, Eat Cheese v1, crackme v3, DOOM Shareware v1, MicroPython v1.0.1, Celeste Classic v1.1, c64emu v2, why2025_sponsors v1, WHY 2025 OTA updater v3, SNAKE! v3, hello v5.

Badge 2 shows 6 Applications Available: WHY2025 Sponsors v1, WHY 2025 OTA updater v4, Name tag v6, SNAKE! v3, hello v5, System settings v1.

How to get the missing apps on the post-event firmware?

[Solved] : Ensure the WIFI and DHCP works...

== Badge Firmware Development related Questions/Issues ==
==== [2] Flashing takes forever (>40 seconds) for a trivial application. Can I speed this up? ====
Yet to be answered.
==== [1] After installing OTA update, application updates AND System Update "BadgeVMS Firmware, Version 4, Main Badge Firmware" the system restarts showing System Updates => "Updates available 1" => "BadgeVMS Firmware, Version 4, Main Badge Firmware". Selecting it, installing it and autorstarting leads back to this same screen. I seem to be stuck in a loop of the update process. ====
* => Shut down your badge by double tapping the power button. Restart. You should now see the application WHY Application Launcher.
** => But double-tapping the power button doesn't shut down the badge...
*** hold ot down for 13+ seconds for a hard reboot.

== BadgeHub related Questions/Issues ==
==== [2] How do I get apps from the BadgeHub onto the Badge? Is it possible without an SD card (I don't have one). I can build apps and flash the firmware, but I have no idea how to get pre-compiled ELFs on there. ====
* => If you have a SD card (if not, the mysteryhack village has a vending machine): Create the folder stucture ./BADGEVMS/APPS on there. In there, create a folder named like the badge hub project name. Download and put the .elf in there. Create a json file with the project name next to the folder and put the key/values for name, unique_identifier, version and binary_path in there. binary_path is just the full name of the .elf file.
** => the mysteryhack village vending machine has been out of SD cards since day 0 or 1

Filesharing

2025-08-11T14:25:18Z

Stored:

Use moar Bandwidth!

{| class="wikitable"

|-
! IP !! Description !! Protocols
|-
| 151.217.147.27 || Decentralized Backup Server || ftp @10Gbit/s!
|-
| 151.217.181.248 || Sharing is Caring || ftp, http (download only), adc(hub on tcp: 5000)
|-
| 151.217.181.231 (now with static ip ... no more dhcp fuckups) || Join the copyparty || ftp (21), http(80), ftps (990) bit broken but this works: ''lftp -u why,why2025 -p 990 151.217.181.231 -e 'set ssl:verify-certificate no; ls'''
|-
| http://151.217.137.46:3923/ || Public-write copyparty server (2TB) || http, https, maybe others idk - '''IP changed'''
|-
| ftp://151.217.176.28 || Random Stuff, public uploads || ftp, http, webdav
|-
| sftp://ftp-srv:why2025@2a05:2d01:2025:1064:225:90ff:fe9a:da2a (camp network only) || tons of DnB 🔥, 4K movies, TV shows, assorted media, ROMs, and other stuff pls feed incoming dir sadly, yolocation '''only''' provided '''1G''' bandwidth this time || sftp only, ftp sucks!
|-
| ftp://[2a05:2d01:2025:1059:1a31:bfff:fe53:f19a] || movies, series, kink p0rn || ftp
|-
| http://151.217.137.48 (offline as of day 4, 12:30) || Public-write CopyParty Server with FLAC music, movies, furry stuff, other :3 || HTTP
|-
| http://151.217.175.23:3923 / http://[2a05:2d01:2025:1048:82c1:6eff:fe08:eae8]:3923 || CopyParty / mirror server, currently downloading a lot of stuff || http / ftp / smb
|-
| DNS: ftp://ftp.yolocation.nl || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv4: ftp://151.217.191.245/24 || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv6: ftp://[2a05:2d01:2025:1064:3eec:efff:fe27:d856] || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv7: Coming Soon... || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| http://151.217.163.231/ || copyparty joined || ftp,http
|-
|}

Filesharing

2025-08-10T11:58:25Z

Stored:

Use moar Bandwidth!

{| class="wikitable"

|-
! IP !! Description !! Protocols
|-
| 151.217.147.27 || Decentralized Backup Server || ftp @10Gbit/s!
|-
| 151.217.181.248 || Sharing is Caring || ftp, http (download only), adc(hub on tcp: 5000)
|-
| 151.217.181.231 (now with static ip ... no more dhcp fuckups) || Join the copyparty || ftp (21), http(80), ftps (990) bit broken but this works: ''lftp -u why,why2025 -p 990 151.217.181.231 -e 'set ssl:verify-certificate no; ls'''
|-
| http://151.217.137.246:3923/ || Public-write copyparty server (2TB) || http, https, maybe others idk - '''IP changed'''
|-
| ftp://151.217.176.28 || Random Stuff, public uploads || ftp, http, webdav
|-
| sftp://ftp-srv:why2025@2a05:2d01:2025:1064:225:90ff:fe9a:da2a (camp network only) || tons of DnB 🔥, 4K movies, TV shows, assorted media, ROMs, and other stuff pls feed incoming dir sadly, yolocation '''only''' provided '''1G''' bandwidth this time || sftp only, ftp sucks!
|-
| ftp://[2a05:2d01:2025:1059:1a31:bfff:fe53:f19a] || movies, series, kink p0rn || ftp
|-
| http://151.217.137.48 || Public-write CopyParty Server with FLAC music, movies, furry stuff, other :3 || HTTP
|-
| http://151.217.175.23 / http://[2a05:2d01:2025:1048:82c1:6eff:fe08:eae8] || CopyParty / mirror server, currently downloading a lot of stuff || http / ftp
|-
| DNS: ftp://ftp.yolocation.nl || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv4: ftp://151.217.191.245/24 || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv6: ftp://[2a05:2d01:2025:1064:3eec:efff:fe27:d856] || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv7: Coming Soon... || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
|}

Filesharing

2025-08-10T11:57:57Z

Stored:

Use moar Bandwidth!

{| class="wikitable"

|-
! IP !! Description !! Protocols
|-
| 151.217.147.27 || Decentralized Backup Server || ftp @10Gbit/s!
|-
| 151.217.181.248 || Sharing is Caring || ftp, http (download only), adc(hub on tcp: 5000)
|-
| 151.217.181.231 (now with static ip ... no more dhcp fuckups) || Join the copyparty || ftp (21), http(80), ftps (990) bit broken but this works: ''lftp -u why,why2025 -p 990 151.217.181.231 -e 'set ssl:verify-certificate no; ls'''
|-
| http://151.217.137.246:3923/ || Public-write copyparty server (2TB) || http, https, maybe others idk - '''IP changed'''
|-
| ftp://151.217.176.28 || Random Stuff, public uploads || ftp, http, webdav
|-
| sftp://ftp-srv:why2025@2a05:2d01:2025:1064:225:90ff:fe9a:da2a (camp network only) || tons of DnB 🔥, 4K movies, TV shows, assorted media, ROMs, and other stuff pls feed incoming dir sadly, yolocation '''only''' provided '''1G''' bandwidth this time || sftp only, ftp sucks!
|-
| ftp://[2a05:2d01:2025:1059:1a31:bfff:fe53:f19a] || movies, series, kink p0rn || ftp
|-
| http://151.217.137.48 || Public-write CopyParty Server with FLAC music, movies, furry stuff, other :3 || HTTP
|-
| http://151.217.175.23 | http://[2a05:2d01:2025:1048:82c1:6eff:fe08:eae8]/ || CopyParty / mirror server, currently downloading a lot of stuff || http / ftp
|-
| DNS: ftp://ftp.yolocation.nl || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv4: ftp://151.217.191.245/24 || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv6: ftp://[2a05:2d01:2025:1064:3eec:efff:fe27:d856] || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv7: Coming Soon... || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
|}

Filesharing

2025-08-10T11:57:13Z

Stored:

Use moar Bandwidth!

{| class="wikitable"

|-
! IP !! Description !! Protocols
|-
| 151.217.147.27 || Decentralized Backup Server || ftp @10Gbit/s!
|-
| 151.217.181.248 || Sharing is Caring || ftp, http (download only), adc(hub on tcp: 5000)
|-
| 151.217.181.231 (now with static ip ... no more dhcp fuckups) || Join the copyparty || ftp (21), http(80), ftps (990) bit broken but this works: ''lftp -u why,why2025 -p 990 151.217.181.231 -e 'set ssl:verify-certificate no; ls'''
|-
| http://151.217.137.246:3923/ || Public-write copyparty server (2TB) || http, https, maybe others idk - '''IP changed'''
|-
| ftp://151.217.176.28 || Random Stuff, public uploads || ftp, http, webdav
|-
| sftp://ftp-srv:why2025@2a05:2d01:2025:1064:225:90ff:fe9a:da2a (camp network only) || tons of DnB 🔥, 4K movies, TV shows, assorted media, ROMs, and other stuff pls feed incoming dir sadly, yolocation '''only''' provided '''1G''' bandwidth this time || sftp only, ftp sucks!
|-
| ftp://[2a05:2d01:2025:1059:1a31:bfff:fe53:f19a] || movies, series, kink p0rn || ftp
|-
| http://151.217.137.48 || Public-write CopyParty Server with FLAC music, movies, furry stuff, other :3 || HTTP
|-
| http://151.217.175.23 || CopyParty / mirror server, currently downloading a lot of stuff || http / ftp
|-
| DNS: ftp://ftp.yolocation.nl || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv4: ftp://151.217.191.245/24 || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv6: ftp://[2a05:2d01:2025:1064:3eec:efff:fe27:d856] || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
| IPv7: Coming Soon... || !!! FEED ME !!! - 108TB || Anonymous FTP - 2x 10Gb - Yolocation
|-
|}

Team:Nuts/heavy power request list

2025-07-22T17:39:36Z

Stored: /* request list */

Request list for heavy power using devices. 

== Heavy power request list ==
On the event there are different pieces of equipment that requere power most of them are your normale 1 phase 16A schuko plug. 
But for al those devices that require more power, 3 phase 16A and up (those red CEE plugs) we want to know about those so it can help us plan the grid. 
So please fill out the form below with the equipment you have that is more then ~9KW (3 phase 16A red cee plug) and up. 

If you have any questions mailing list: nuts@lists.why2025.org 

== example ==
EXAMPLE!
{| class="wikitable"
|+ List of requests
|-
! Team !! location !! equipment !! power usage and plug type !! note !! Nuts approval !! nuts note
|-

| [[Team:Waste]] || boneyard || garbage compactor || 3 phase 16A CEE || to get rid of carbage || - || -
|-

| [[Team:Productiehuis]] || main stage|| stage power || 3 phase 200A powerlock || power for main stage || - || -
|-
|-
|}
EXAMPLE!

== request list ==

{| class="wikitable"
|+ List of requests
|-
! Team !! location !! equipment !! power usage and plug type !! note !! Nuts approval !! nuts note
|-
| [[Team:Productiehuis]] || Andromeda || AV + LED wall || 2x 63A CEE + break-out || Way more than consumed but large headroom needed|| ✅ ||
|-
| [[Team:Productiehuis]] || Brachius || AV + displays || 1x 63A CEE + break-out || Way more than consumed but large headroom needed || ✅ ||
|-
| [[Team:Productiehuis]] || Cassiopeia || AV + displays || 1x 32A CEE + break-out || Way more than consumed but large headroom needed || ✅ ||
|-
| [[Team:Productiehuis]] || Delphius || AV + displays || 1x 16A CEE + break-out || Way more than consumed but large headroom needed || ✅ ||
|-
| [[Team:Productiehuis]] || Workshop Euclid || AV + displays || 1x 16A CEE + break-out || || ✅ ||
|-
| [[Team:Productiehuis]] || Workshop Fobos || AV + displays || 1x 16A CEE + break-out || || ✅ ||
|-
| [[Team:Shuttle]] || Parking area || BEV Charging || 40kWp, 63A CEE || topping up Shuttle vans (5 cars) || ✅ || Including charge infrastructure for up to 8 connections
|-
| [[Team:NOC]] || Datacenter || 4x7KW air conditioning || 28KW ,32A CEE with breakout || cooling Datacenter || ✅ || -
|-
| [[Team:NOC]] || Datacenter || servers || 2x 32A CEE seperate feed with breakout || servers || ✅ || -
|-
| [[Team:NOC]] || NOC || computers || 1x 16A CEE with breakout || computers || ✅ || -
|-
| [[Team:NOC]] || Datenklo (56x) || switches || 1x 16A schuko, no shared RCD/FUSES, prevent going down. || if datenklo if not beside a power point a extension cord is needed. can this be supplied by NUTS?|| ✅ ||
|-
| [[Village:DutchPicknick]] || [[Village:DutchPicknick]] ||Kitchen equipement, lights, audio equipment, beamer, stagelights, power for sleeping places, cooling trailer, servers || 1x 3x400V+N 32A CEE || Provide 60 residents with an enjoyable WHY2025 and we have our own distributionpoints from 32A/400V to 3x 230V (L1/L2/L3) for use inside the village || ||
|-
| [[Village:Squirrel (Brussels)]] || [[Village:Squirrel (Brussels)]] || Multiple various equipments, deep fryers, and servers || 1x 3x400V+N 32A CEE || Break-out box provided + 20 m of 32A extension cord || ✅ || -
|-
| [[Team:On-site_transportation]] || LSD || Electric Telehandler|| normal charge 3 kW (240 V / 16 A) blue CEE, quick charge 18 kW (415 V / 32 A) || normal charge might be enough, maybe quick charge if needed at shuttle charging area. [https://broekveldt.nl/wp-content/uploads/2023/04/Specificaties-525-60E.pdf Spec sheet] || ✅ || -
|-
| [[Team:Safety-Fire]] || Safety village || AC, hot water || Stopcontact 230V 2x vrije groep (2x CEE 230V/16A) || Housing 'afkoelruimte' || ✅ || -
|-
| [[Team:Safety-Fire]] || Safety village || AC, Nighttime-Cooking, washing machine, hot water || Stopcontact 230V 2x vrije groep (2x CEE 230V/16A) || Housing 'piketdienst' || ✅ || -
|-
| [[Team:Safety-Fire]] || Safety village || AC, hot water || Stopcontact 230V 2x vrije groep (2x CEE 230V/16A) || Housing 'centrale post' || ✅ || -
|-
| [[Team:Safety-Fire]] || Safety village || hot water || Stopcontact 230V 1x vrije groep (1x CEE 230V/16A) || Firt-aid tent || ✅ || -
|-
| [[Team:Volunteers]] || Heaven || hot water & kitchen equipment || A lot (details will follow) Induction cooking plate, steam ovens, lighing for big tent, 4 workspaces, 2 tables with outlet|| Heaven || ✅ || -
|-
| [[Team:Volunteers]] || Heaven cool container || As early as possible, day -6 || 2 cooling containers || [https://map.why2025.org/?building=60 Koelcontainer naast heaven] || ✅ || -
|-
| [[Team:Warehouse]] || Warehouse || 4 portacabins || 1x 32A red uplink, 3x 32 A short link (assumption! to be confirmed with rental company) || <s>will probably only use <5 kW in practice; at most twice that, when it's very cold or hot</s> Change of plans: we will use more power than previously indicated; 3x32 A still suffices but we will actually use more (because of charging 2 gators) || ✅ || -
|-
| [[Team:Foodcourt]] || Foodcourt || Foodtrucks & cooling container || 67kW Peak usage, 9 trucks, cooling container (13kW 32A CEE) Total: 13x 16A groups. 4x 32A CEE || - || ✅ || -
|-
| [[Team:Bar]] || Bar Foodcourt (+ backstage) || Bar equipment || ~54kW 4x32A CEE + 12x 16A group || See [[Team:Bar]] page for full table. || ✅ || -
|-
| [[Team:Bar]] || Bar Main Stage || Bar equipment || ~27kW, 1x32A CEE 5-Pole + 8x 16A group || See [[Team:Bar]] page for full table. || ✅ || -
|-
| [[Team:Bar]] || Bar Arcade || Bar equipment || ~30kW, 1x32A CEE 5-Pole + 9x 16A group || See [[Team:Bar]] page for full table. || ✅ || -
|-
| [[Team:Ticket_%26_Entrance]] || Entrance || Charging laptops, lamps || 5x Stopcontact 230V || distrib. over two tables in 5by10 tent || ✅ || -
|-
| [[Team:CTF]] || CTF Tent || Workspaces for 75 visitors + lighting (led), a fridge, water cooker, popcorn machine, toaster & networking equipment || All normal 230v sockets || We provided a floorplan via email. We have been in contact with Team:Warehouse as well, which pointed us back to you. || ✅ || -
|-
| [[Village:WOC]] || Pagode Tent WOC || Power for Waffle irons, fridges, ice rolls, kitchen stuff in the WOC Village… || ~20kW 12x230V Schuko || - || ✅ || -
|-
| [[Project:Arcade]] || Arcade tent || 50 Arcade cabinets and pinballs, lights, projectors etc. || About 20kW total, maybe a little bit more. All machines use schuko. || - || ✅ || -
|-
| [[Team:PartyArea]] || PartyArea || Lights and Audio equipment || 100kW Peak usage (during evening hours), 3x 32A CEE for Lights (located on/under stage) 2x 32a for Audio (located on/under stage) total: 5x 32A CEE || - || ✅ || 125A + distribution
|-
| [[Team:Waste]] || LSD || Trash compactor || 5,5kW, 400V 32A stekker afzekeren: C 25A || Will be on the field from 01-08 until 14-08 || ✅ || 13/14-8 with mobile generator?
|-
| [[Team:Waste]] || Foodcourt || Trash compactor || 5,5kW, 400V 32A stekker afzekeren: C 25A || Will be on the field from 01-08 until 14-08 || ✅ || 13/14-8 with mobile generator?
|-
| [[Village:Area42]] || Area42/Cluster D42D || Kitchen equipment, lights, audio equipment, power for sleeping places (incl. some medical stuff), etc.|| 31KW Peak (most likely during early morning hours and late afternoon for cooking activities), 1x 63A CEE (we will distribute further down ourselves) || - || ✅ || -
|-
| internal tents || tracks, workshops, family, heaven || Long thick industrial extension leads +schuko || || in the past, we rented a few m3 of these|| tbd || -
|-
| [[Village:ChaosFurs]]|| tbd || Village distribution (smoke machine, single induction cooker, partylights, audio, small fridge, projector) || 32A/400V (we have our own distribution box and have 32A/400V and 16A/400V out to daisy chain to next box if needed) || || ✅ || -
|-
| [[Village:Food_Hacking_Base]]|| Food Hacking Base village || Kitchen equipment, cooling trailer || 32A/400V || we have our own distribution box and have 32A/400V and 16A/400V out to daisy chain to next box if needed || tbd || Location?
|-
| [[Village:Yolocation]]|| Popup datacenter for Free VMs || Datacenter and server equipment || 32A / 400V CEE We have our own fused distribution box to 6x16A 230V || 7/8-13/8 || - ||
|-
| [[Team:productiehuis]]|| all track tents|| power on day -4 || - || - || tbd || On priority list; no guarantee
|-
| [[Project:Sauna]] || Sauna near [[Village:Salmiakki]], [https://map.why2025.org/#maphash=22/52.69234934/4.74498189/-20 map link] || Sauna stove + hacktent + tents || 1x 32A CEE (we split it with own distribution box to 3x16A for sauna and 3x16A to rest)|| || tbd ||
|-
| [[Village:ANDERSTORPSFESTIVALEN]] || Bar right of event party bar || PA, Bar equipment, fridges || 1x 32A / 400V CEE (we have our own distribution box) || If possible we'd like power from day -2 (5th) || tbd ||
|-
| [[Cluster:Chaos_Norden_Westen_Osten_%2B_Austria]] || Chaos DACH cluster next to Datenklo M11 || kitchen equipment, networking equipment, uplink for Yolocation, lights and audio || 1x 32A CEE || If possible we'd like power from day -2 (5th) || - || -
|-
| [[Village:Nbsp]] || Violet Field || Domes and Dome accessories || 2x 3 phase 16A CEE || email if there are issues; 32A 3P or multiple seperate phases may be doable || - || -
|-
| [[Village:Milliways]] || Milliways Cluster south of food court || 2x Cooling Trailers, JungleDome, lighting, DJ Booth, Kitchen Equipment and more || 2x 32A / 400V CEE (we have our own distribution boxes) || If possible we'd like power from day -2 (5th) || tbd ||
|-
| [[Village:Back_to_the_80s_Party]] || Village Back to the 80s Party || Audio, kitchen equipment, cooling, party lights, overhead projector, beamer, laptops, pinball machine || 3 phase 400V 16A CEE (we have our own distribution box) || || tbd ||
|-
| [[Village:Hardware_Hacking_Area]] || Village Hardware Hacking Area || 80 soldering irons (30W each), 10 lamps (25W each), 40 laptops (200W each) || ~10KW, Schuko || || tbd ||
|-
| [[Village:ZTL]] || Village ZTL || Lights, Fridge, Induction Cooker, Oven, Soldering Equipment || 3 phase 400V 16A CEE (we have our own distribution box) || distribution box has additional CEE socket for further distribution + we bring 10m of cable but could bring more if necessary) || tbd ||
|-
| [[Village:SHA512]] || Village SHA512 || Lights, Fridge, Induction Cooker, Soldering Equipment, Microscope and other hardware hacking equipment || 3 phase 400V 16A CEE (we have our own distribution box) || || tbd ||
|-
| [[Team:POC]] || POC || Fridge, Freezer, Deepfryer, Oven, DECT (A LOT), Lights, Projectors, Computers || 1x 16A CEE || We need at least Basic Power on 02. August || - ||
|-
| [[Village:Energy]] || Village Energy || Lights, Fridge, (Water)Cooker, Soldering Equipment, Computers, Projectors, Networking || 3 phase 400V 16A CEE (we have our own distribution box) || || tbd ||
|-
| [[Village:Entropolis]] || Village Entropolis || Lights, Fridge, Electric / Induction Cooker, Coffee Machine, Kettle, Soldering Equipment, Computers, Projectors, Networking, || 3 phase 400V 16A CEE (please provide distribution box if possible) || || tbd ||
|}

Village:Entropolis

2025-07-07T16:18:06Z

Stored:

{{Village
|Has name=Entropolis
|Has website=entropia.de
|Has contact=why2025@entropia.de
|Has description=Entropia @ WHY2025 :)
|Related to village=Village:ZTL, Village:WOC
|Part of=Chaos Mauldasch
|Has village tag=Hacking, Healthcare, Cybersecurity, zfs, software, queer, comfort, hacking, education, networking
|Provides session location=No
|Location=52.69169, 4.74778
|Has orga contact=info@entropia.de
|On site orga contact=7867
|Village citizen count=30
|Village Needs power=Large Village (32A CEE 400V)
|Village size needed=200
|Village hacktents num=3
|Village brings big stuff=Maybe
|Village planning notes=We will most likely bring 3 big tents (8x12 meters)
}}
The Entropia will be present at WHY2025 with it's very own Village! We might cook some gulasch, hack some things and build a hot tub, who knows?

This is our vacation from the GPN, so we will take it easy. Though some glamping will happen :P

Village:Entropolis

2025-07-07T16:01:35Z

Stored:

{{Village
|Has name=Entropolis
|Has website=entropia.de
|Has contact=why2025@entropia.de
|Has description=Entropia @ WHY2025 :)
|Related to village=Village:ZTL
|Part of=Chaos Mauldasch
|Has village tag=Hacking, Healthcare, Cybersecurity, zfs, software, queer, comfort, hacking, education, networking
|Provides session location=No
|Location=52.69169, 4.74778
|Has orga contact=info@entropia.de
|On site orga contact=7867
|Village citizen count=30
|Village Needs power=Large Village (32A CEE 400V)
|Village size needed=200
|Village hacktents num=3
|Village brings big stuff=Maybe
|Village planning notes=We will most likely bring 3 big tents (8x12 meters)
}}
The Entropia will be present at WHY2025 with it's very own Village! We might cook some gulasch, hack some things and build a hot tub, who knows?

This is our vacation from the GPN, so we will take it easy. Though some glamping will happen :P

Village:Entropolis

2025-07-07T15:59:21Z

Stored:

{{Village
|Has name=Entropolis
|Has website=entropia.de
|Has contact=why2025@entropia.de
|Has description=Entropia @ WHY2025 :)
|Related to village=Village:ZTL
|Has village tag=Hacking, Healthcare, Cybersecurity, zfs, software, queer, comfort, hacking, education, networking
|Provides session location=No
|Location=52.69169, 4.74778
|Has orga contact=info@entropia.de
|On site orga contact=7867
|Village citizen count=30
|Village Needs power=Large Village (32A CEE 400V)
|Village size needed=200
|Village hacktents num=3
|Village brings big stuff=Maybe
|Village planning notes=We will most likely bring 3 big tents (8x12 meters)
}}
The Entropia will be present at WHY2025 with it's very own Village! We might cook some gulasch, hack some things and build a hot tub, who knows?

This is our vacation from the GPN, so we will take it easy. Though some glamping will happen :P

Village:Entropolis

2025-06-24T15:52:06Z

Stored:

{{Village
|Has name=Entropolis
|Has website=entropia.de
|Has contact=why2025@entropia.de
|Has description=Entropia @ WHY2025 :)
|Related to village=Village:ZTL
|Has village tag=Hacking, Healthcare, Cybersecurity, zfs, software, queer, comfort, hacking, education, networking
|Provides session location=No
|Location=52.69094, 4.74245
|Has orga contact=info@entropia.de
|On site orga contact=7867
|Village citizen count=30
|Village Needs power=Large Village (32A CEE 400V)
|Village size needed=200
|Village hacktents num=3
|Village brings big stuff=Maybe
|Village planning notes=We will most likely bring 3 big tents (8x12 meters)
}}
The Entropia will be present at WHY2025 with it's very own Village! We might cook some gulasch, hack some things and build a hot tub, who knows?

This is our vacation from the GPN, so we will take it easy. Though some glamping will happen :P

Village:Entropolis

2025-05-15T11:19:31Z

Stored:

{{Village
|Has name=Entropolis
|Has website=entropia.de
|Has contact=why2025@entropia.de
|Has description=Entropia @ WHY2025 :)
|Related to village=Village:ZTL
|Has village tag=Hacking, Healthcare, Cybersecurity, zfs, software, queer, comfort, hacking, education, networking
|Provides session location=No
|Location=52.69094, 4.74245
|Has orga contact=info@entropia.de
|On site orga contact=7867
|Village citizen count=35
|Village Needs power=Large Village (32A CEE 400V)
|Village size needed=200
|Village hacktents num=3
|Village brings big stuff=Maybe
|Village planning notes=We will most likely bring 3 big tents (8x12 meters)
}}
The Entropia will be present at WHY2025 with it's very own Village! We might cook some gulasch, hack some things and build a hot tub, who knows?

This is our vacation from the GPN, so we will take it easy. Though some glamping will happen :P

Village:Entropolis

2025-02-18T14:52:01Z

Stored:

{{Village
|Has name=Entropolis
|Has website=entropia.de
|Has contact=why2025@entropia.de
|Has description=Entropia @ WHY2025 :)
|Related to village=Village:ZTL
|Has village tag=Hacking, Healthcare, Cybersecurity, zfs, software, queer, comfort, hacking, education, networking
|Provides session location=No
|Location=52.69094, 4.74245
|Has orga contact=info@entropia.de
|On site orga contact=7867
|Village citizen count=30
|Village Needs power=Large Village (32A CEE 400V)
|Village size needed=150
|Village hacktents num=3
|Village brings big stuff=No
}}
The Entropia will be present at WHY2025 with it's very own Village! We might cook some gulasch, hack some things and build a hot tub, who knows?

This is our vacation from the GPN, so we will take it easy. Though some glamping will happen :P

User:Stored

2025-02-18T14:51:33Z

Stored:

{{UserInfo
|Name=stored
|Bringing=Camping Gear, Servers, Village Assembly
|Village=Village:Entropolis
|EMail=why2025@stored.cc
|Mastodon=@storedcc@chaos.social
|DECT=7867
|Languages=EN,DE
|HackerSpace=Entropia
|NickName={{PAGENAME}}
}}

User:Stored

2025-02-18T14:51:20Z

Stored:

User:Stored

2025-02-18T14:50:22Z

Stored:

{{UserInfo
|Name=stored
|Bringing=Camping Gear, Servers, Village Assembly
|Village=Village:Entropolis
|Languages=EN
|NickName={{PAGENAME}}
}}

User:Stored

2025-02-18T14:49:54Z

Stored:

{{UserInfo
|Name=stored
|Languages=EN
|NickName={{PAGENAME}}
}}

Village:Entropolis

2025-02-18T14:33:53Z

Stored:

{{Village
|Has name=Entropolis
|Has website=entropia.de
|Has contact=henry@entropia.de
|Has description=Entropia @ WHY2025 :)
|Related to village=Village:ZTL
|Has village tag=Hacking, Healthcare, Cybersecurity, zfs, software, queer, comfort, hacking, education, networking
|Provides session location=No
|Location=52.69094, 4.74245
|Has orga contact=info@entropia.de
|On site orga contact=7867
|Village citizen count=30
|Village Needs power=Large Village (32A CEE 400V)
|Village size needed=150
|Village hacktents num=3
|Village brings big stuff=No
}}
The Entropia will be present at WHY2025 with it's very own Village! We might cook some gulasch, hack some things and build a hot tub, who knows?

This is our vacation from the GPN, so we will take it easy. Though some glamping will happen :P

Village:Entropolis

2025-02-18T14:29:38Z

Stored:

Village:Entropolis

2025-02-18T14:27:59Z

Stored:

File:Village-Entropolis.png

2025-02-18T14:24:07Z

Stored:

Village:Entropolis

2025-02-18T14:22:37Z

Stored: Created page with "{{Village |Has name=Entropolis |Has website=entropia.de |Has contact=henry@entropia.de |Has description=Entropia @ WHY2025 :) |Related to village=Village:ZTL |Has village tag=Hacking, Healthcare, Cybersecurity, zfs, software, queer, comfort, hacking, education, networking |Provides session location=No |Has orga contact=info@entropia.de |On site orga contact=7867 |Village citizen count=30 |Village Needs power=Large Village (32A CEE 400V) |Village size needed=150 |Village..."

User:Stored

2025-02-18T14:15:33Z

Stored: create user page

{{UserInfo
|NickName={{PAGENAME}}
|Languages=EN
|HackerSpace=
}}